™Request a compatibility review ↗

Manufacturing / Maintenance, repair & operations

Industrial
Maintenance
Degreaser.

Parts washing, machine maintenance and facility cleaning.

GreaseCheck is a neutral pH aqueous degreaser supplied by LKA Industrial Solutions Inc. for industrial maintenance, parts washing and facility cleaning. Working solutions remove oils, grease and accumulated shop soils. Released oil can separate on standing in soak tanks, supporting skimming and reuse when bath condition and the cleaning result remain acceptable.

Illustration of gloved hands brushing a steel gear over an industrial parts washer.
Industrial MRO / Parts washing
Working solution pH7.0–7.5
01 / CHEMISTRY7.0–7.5pH at working dilution
02 / FLASH POINTNoneAqueous solution · see SDS
03 / TRANSPORTDOT not regulatedProduct shipping classification
04 / WORKING SOLUTIONVOC below 0.5%As stated in the product TDS

Maintenance applications

Parts washing, machinery
and facility floors.

Choose concentration and process conditions for the component and the soil.

01

Parts & tooling

Aged grease, accumulated oil and baked-on films in parts washers, soak tanks or manual cleaning.

Industrial · 1:3 ↗
02

Machine maintenance

Oil and grease on machine housings, fixtures and accessible maintenance surfaces.

Industrial · 1:3 ↗
03

Shop & facility floors

Light oils and routine shop soils on compatible floors using mop, wipe or a suitable scrubber.

Multipurpose · 1:10 ↗

How it works

Three mechanisms.
One cleaning solution.

Solvency, detergency and chelation act together. This is a simplified process illustration, not a molecular model.

01 / SOLVENCY

Penetrate the deposit

A coupling solvent loosens oils, baked-on films and deposits.

02 / DETERGENCY

Lift the loosened soil

An anionic surfactant carries loosened contamination into the water phase.

03 / CHELATION

Address metallic soaps

A water-conditioning agent helps break down metallic soaps and supports use in hard water.

Material compatibility

Material compatibility
and exposure conditions.

Application guidance from the published TDS. A neutral pH does not replace a material-specific check.

Material review guide
MaterialPublished guidanceBefore full use
Steel & cast ironRinse and dry promptly; rust prevention may be needed.Check flash-rust control and downstream finishing.
Aluminium & anodised finishesThe TDS describes compatibility with these surfaces.Test the alloy, coating condition and proposed contact time.
Paint & coated surfacesTest an inconspicuous area before use.Check finish condition, adhesion and exposure.
EPDM / NitrileNo grade-specific exposure table is published in the supplied sheets.Request review using grade, temperature and exposure duration.
Request a material-specific review ↗

Dilution & yield

One concentrate.
Mix for the task.

Ratios are concentrate : water.
Add water first, then concentrate.

US gal
—US gal concentrate
+
—US gal water
4 galworking solution from
1 US gal concentrate

Final solution volume, not concentrate volume. Mixing assumes additive volumes. Follow the applicable TDS. Total job consumption depends on the deposit and cleaning method.

Application guide

Set the process around the part.

01 / PREPARE

Review the materials

Identify the alloy, coating and elastomer grade. Confirm the parts washer or scrubber requirements.

02 / CLEAN

Mix for the task

Industrial 1:3: 2–5 minutes on heavy deposits. Multipurpose 1:10: up to 1–2 minutes on soiled areas. Agitate as needed.

03 / FINISH

Rinse, dry & inspect

Follow the selected TDS. Rinse and dry bare mild steel and cast iron promptly; assess rust prevention where needed.

PPE and ventilation

Use safety glasses. Wear chemical-resistant gloves for prolonged or repeated contact. Provide ventilation when spraying and avoid atomising the solution into fine mist. Consult the SDS for the product being handled.

Automatic floor scrubbers

The Multipurpose TDS lists automatic floor scrubber application. Confirm foam control and machine requirements before use. The concentrate has moderate foam; do not assume all dilutions suit all machines.

Technical documents

Check the data.
Choose the right sheet.

SDS and TDS for the concentrate and all three working solutions. PDFs hosted on greasecheck.com.

Working solution ratings do not replace the handling requirements for concentrate. Consult the sheet for the product you are using.

Material Compatibility Review

Bring the material.
And the operating conditions.

A useful compatibility review starts with the substrate, finish, deposit and actual contact conditions. Include the elastomer grade or equipment documentation where available.

01 Identify the material and coating.

02 Describe concentration, temperature and contact time.

03 Agree a small-scale test before full application.

Complete the details below to prepare an email to our team. Send the message from your email app to submit your request.

Opens your email app with a draft. Your request is sent only when you press Send there. Prefer webmail? Copy the request below and send it to sales@greasecheck.com.

Copy request for webmail