™Request an oilfield pilot ↗

Oilfield / Rig & yard maintenance

Rig & Yard Wash
Degreaser.

For rigs, pumpjacks and equipment yards.

GreaseCheck is a water-based industrial degreaser supplied by LKA Industrial Solutions Inc. for oilfield equipment and maintenance yards. Its neutral pH working solutions target grease, oil and accumulated industrial soils. Select a dilution for the deposit, check the equipment materials and confirm performance on representative drilling muds and thread compounds.

Illustration of a pumpjack and steel equipment in an oilfield maintenance yard.
Oilfield / Equipment yard
Working solution pH7.0–7.5
01 / CHEMISTRY7.0–7.5pH at working dilution
02 / FLASH POINTNoneAqueous solution · see SDS
03 / TRANSPORTDOT not regulatedProduct shipping classification
04 / WORKING SOLUTIONVOC below 0.5%As stated in the product TDS

Oilfield applications

Rig equipment, production units
and service fleets.

Use the same concentrate across the yard. Verify performance on your actual soil and equipment.

01

Drilling equipment

Oil and accumulated grease on accessible rig equipment, frames and housings.

Industrial · 1:3 ↗
02

Pumpjacks

Grease deposits and oily soils on accessible exterior surfaces of production equipment.

Industrial · 1:3 ↗
03

Thread compounds

Evaluate removal on your pipe-dope formulation. Metallic soaps and additives vary by product.

Industrial · 1:3 ↗
04

Oil-based mud residue

Test representative drilling mud and mixed deposits before defining the wash process.

Industrial · 1:3 ↗
05

Frac & service fleets

Routine degreasing of equipment bodies, frames and wheels in a controlled wash area.

Heavy Duty · 1:6 ↗
06

Equipment yards

Maintain washable support equipment and work areas. Collect oily wash water for site handling.

Heavy Duty · 1:6 ↗

Dilution & yield

One concentrate.
Mix for the task.

Ratios are concentrate : water.
Add water first, then concentrate.

US gal
—US gal concentrate
+
—US gal water
4 galworking solution from
1 US gal concentrate

Final solution volume, not concentrate volume. Mixing assumes additive volumes. Follow the applicable TDS. Total job consumption depends on the deposit and cleaning method.

Application planning

A wash routine the crew can repeat.

01 / CHECK

Confirm the surface

Identify coatings and sensitive components. Test a small area. Follow the site’s isolation and wash-water procedures.

02 / APPLY

Use the selected mix

Industrial 1:3: allow 2–5 minutes. Heavy Duty 1:6: allow 1–3 minutes. Agitate where needed and avoid fine mist.

03 / RINSE

Inspect before repeating

Rinse thoroughly. Check the finish and remaining deposits, then record any repeat pass in the trial data.

Working solution properties & operator protection

The SDS lists NFPA 704 0/0/0 for working solutions. This is not a site risk rating. Use safety glasses and the specified site PPE; gloves are recommended for prolonged or repeated contact. Ventilate spray work and avoid fine mist.

Cleaning safety-critical assemblies

Cleaning guidance does not authorize disassembly, servicing or treatment of safety-critical internals. Check equipment manufacturer requirements before treating seals, controls or sensitive assemblies.

Technical documents

Check the data.
Choose the right sheet.

SDS and TDS for the concentrate and all three working solutions. PDFs hosted on greasecheck.com.

Working solution ratings do not replace the handling requirements for concentrate. Consult the sheet for the product you are using.

Oilfield Pilot Request

Plan a two-week field comparison.

Tell us which equipment and deposits you want to test. A proposed two-week pilot records dilution, contact time, rinse water and crew time against your current process.

01 Choose comparable equipment and a clean standard.

02 Record each wash, including repeat passes.

03 Review the finish, operator feedback and total cost.

Complete the details below to prepare an email to our team. Send the message from your email app to submit your request.

Opens your email app with a draft. Your request is sent only when you press Send there. Prefer webmail? Copy the request below and send it to sales@greasecheck.com.

Copy request for webmail